Did you know?

Hi I was wondering if you could assist me with some issues I am having with my litter robot 2. For some reason it is rotating in the wrong direction (anticlockwise) with the Amber light constantly on. I have replaced the control board after ordering from your shop, which seemed to fix the issue but when I checked this morning the litter hasn’t …The Litter-Robot is equipped with an Anti-Pinch safety feature to make the Litter-Robot extra safe for your cat. While cycling, if a potential pinch condition is detected, the globe will stop and reverse direction for 2 seconds. The yellow light will begin flashing quickly, about four times per second. You will also receive a notification on ...What Happens if the Litter Robot Globe Jams? If the Litter-Robot globe jams, the motor will stop and reverse for a few seconds. The unit will then try to cycle again three times. If it cannot cycle after three …Jan 11, 2023 · Troubleshooting Common Problems with the Litter Robot. If your Litter Robot isn’t cycling, there are several potential causes that you should investigate. Before attempting to reset or re-calibrate your Litter Robot, try the following troubleshooting steps: Check the Power Source. The first step is to check the power source.Litter-Robot 3: Cycle delay setting. The cycle delay is the elapsed time starting from when your cat exits the globe until the unit starts a clean cycle. It can be set for 3, 7, or 15 minutes. The default cycle delay is 7 minutes. Reduce the cycle delay if it is important to minimize odor and/or the time that waste is accessible to other pets ...Hi! I require your help regarding a problem I’m encountering my litter robot 3 worked fine for a month or so No it has been stopping in the middle of cycles with a cat interrupt sensor error, the cat is not in the litter. I’ve tried pressing cycle to resume the cycle and the litter-robot app keeps sending notification about cat sensor interrupt. I’ve …Get started by following the steps below. If possible, place Litter-Robot in the same location as the old litter box (at least during transition). Make sure the unit is on a firm, level surface in a cool, dry location. Locate the unit near a power outlet. Ensure the unit isn’t pushed against a wall or into a corner (must not be touching any ...Check for excess weight, such as too much litter or waste. When you are done, press the Reset button to reset the cat sensor. If the cycling light is slowly flashing yellow (about once per second) or you are receiving a Cat sensor interrupt or Bonnet removed notification, this indicates a cycle has been interrupted by a cat entering the globe ...The Litter Robot Open Air III should be cleaned completely every 1-3 months. We usually wait three months to clean it with our two cats, but probably should do it sooner. It takes about 15-20 minutes to clean the litter robot, and another 10 to dry and assemble. It will smell great when you’re done! When Should I Clean My Litter RobotLitter-Robot 4: Blue light bar with yellow blinking WiFi (Onboarding mode) Litter-Robot 4: Blue with partial yellow flashing (Excess weight detected) Litter-Robot 4: Calibrating OmniSense Laser Sensors. Litter-Robot 4: Connect light status (WiFi) Litter-Robot 4: Control Panel - Button Functions.How to Install a Waste Drawer Liner. 1- Remove the old bag. 2- Wipe the DFI sensor’s circuit boards on each side. 3- Install the new bag. 4- Press the “Reset” button on the robot. 5- Reset the level on the app. (For wi-fi model) Note: Steps 4 and 5 must be done in that order according to the manufacturer’s instructions.litter robot4: litter robot control software: Factory reset, tested with other cats, tried to manually cycle from the controls will works, lifted the globe to see if there is litter in the working mechanisim, tested with less than recommended litter level: Automatic cycles troubles from day 1 of operation: Thank you so much in advance for your ...My litter robot two lights are sticking on. The reset and empty buttons wont turn off. If i hit recycle it will cycle however when its done recycling the two light stag on again. I have unplugged it . I have trued everything. Its not over filled with litter. Its actually below the line. The only time it recycles is when i hit the recycle button.emptying the robot of litter entirely, cycling, and then adding litter again The litter level reader is still inaccurate. I eventually added some new litter yesterday, bringing it to the “optimal” level in the robot. Now the app finally reads that the robot is halfway-full of litter (an increase from the “low” reading).

Cover the light sensor which is located under the power button. If the night light turns on and the cycle is interrupted, then your bonnet needs to be replaced. It is possible that the night-light is not even working, in this case, please remove the power from the robot and unclip the bonnet. Inside the bonnet you will see 2 wires connected to ...Brand new Litter Robot flashing Blue - Red Sequentially. Hey everyone - we got a Litter Robot and it started flashing Blue then Red immediately after running a cycle. Chatted with customer service and they said it was an over-torque issue. They sent a new base yet I'm getting the same flashing Blue - Red lights.May 29, 2017 · We recommend leaving the Litter-Robot off and. operating in “semi-automatic” mode. When you see. your cat has used the Litter-Robot, turn it on, and. the Litter-Robot will automatically perform a Clean. cycle. Once it finishes (about 2 1⁄2 minutes), turn the. power off. This way, your kitten is safe while it gets.It’s important to pay attention to your cat's behavior to pinpoint the reason behind their sudden litter box aversion. In some cases, medical issues will cause your cat to stop using the litter box. In other cases, your feline’s litter box aversion could stem from something as simple as not liking the litter in their box.

Why Isn’t My Litter-Robot Cycling on its Own? It’s probably a sensor problem. You should first try to cycle it manually. Press the Cycle button. If it does work, move on to the next step. Now, try to reset the sensor by shutting the unit with the power button. When it’s starting up, push on the robot to see if the sensor actually does ...Disconnect the bonnet. Gently flex the two front bonnet tabs outward and hold for about 20-30 seconds. Reattach the bonnet. There are four tabs total: two in the back, two on the sides. You should feel a secure snap and hear a “click” when placed back into the slot, and the bonnet should sit closer to the base.…

Reader Q&A - also see RECOMMENDED ARTICLES & FAQs. Litter-Robot 4: Light codes guide. Litter-Robot 4 control p. Possible cause: I require your help regarding a problem I’m encountering. Stops cycling.